circuit
MCDI
tlr+ specifications
Products Guide go to download section display contacts and general info see our distributors on the www
innovation in security
   
go to dutch main page
go to deutsch distributors page
HOME PAGE
TLR+ ESPANOL
SPECIFICATIONS DU TLR+
TLR PLUS SPECIFICATIONS
go to chinese main page
home page

Description

TLR+ is an enhanced performance version of the TLR, MCDI’s popular PC-based twin-line alarm receiver card.
TLR+ uses a high-performance micro-controller and can be installed in any standard chassis IBM™ or compatible PC - AT, 386, 486 or Pentium™. TLR+ can interface to two telephone lines, with no limit on the number of customers per line. It provides a DB25 parallel printer port.
With expanded memory, faster modem circuitry, improved PC bus interface and Caller ID option, TLR+ adds many new and attractive features to the basic Monitoring Station.
Option: Remote display / control unit. Packaged as stand alone device or fitted in PC’s CD anchor slot.
Certification
FCC(USA), IC(Canada), CE-Security (Europe), CE-0560 Telecom (Europe), ICT D800-428K (Germany), IBPT TC970587 (Belgium) and South Africa (ZA TE-2000/079).

Features
- Supports SIA, CFSK, VFSK
- Caller Identification (Option)
- Internal buffer - 800 to1000 Events
- CMOS Lithium battery for non volatile memory
- Dead line detection
- Up to eight receivers per PC
- Supports software retransmit function
- Configureable address and IRQ
- Alert/Warning buzzer
- Supervision of back-up battery
- Selectable Monitoring software interfaces
- Listen-in, Two way voice
- Remote control and display (option)


Specifications

Communications:
TLR+ provides an RJ11 type phone jack for connection to one or two telephone lines.
Type : Pulse, DTMF, FSK
Reception Speed : 10, 20, 40 pps DR / CS
Handshake and Kiss-off : 1400Hz / 2300Hz/2225Hz
Pulse Frequency//Telim : 1800Hz / 1900H//1100Hz

Reception Formats supported
:

Acron MCDI TAL
Ademco: Napco Point ID
-Slow/Fast Radionics 6500
-Contact ID Radionics extended
-Extended Sescoa Slow, Super Fast
-Express Sescoa Standard
-High Speed SIA
BFSK, CFSK, VFSK Silent Knigh Slow
FBII Super Fast Stratel
3x1 3x1 extended
4x1 3x1 extended compressed 4x2
4x1 extended 4x1 extended compressed 4x2
4x2 Zero removed 3x1,4x1, extended
Optex's Varitech C&K: Bell 103A2 or CCIT(option)

For Germany and Scandinavia, as Pulse replacement:
Telim Robofon

Printer Output:
- Standard DB25 connector for Centronics Parallel Interface.

- Card linking arrangement allowing one printer to serve all TLR Plus receivers in one PC.

Event Logging when PC is absent:
TLR+ can store up to 800 events (Native mode), 1000 events (Ademco 685 / Surgard mode).
Specifications

Power Requirements:
From computer +12V Supply: 500 mA max.
From 6V Battery (standby): 500 mA

Port & IRQ:
Port address is configured by rotary switch and IRQ by setup program:
- COM 1 , 2, 3, or 4 and up to 16 addresses
- IRQ 3, 4, 5, 9,10,11, 12, 14, 15.

Battery Back-up:
TLR+ provides charging and supervision circuitry for an external 6-Volt battery (not supplied).

Charging Voltage 6.7 volts
Charging Current Limit 500 mA

Station Requirements:
- IBM™ or Compatible AT, 386, 486 or Pentium™ computer with Standard chassis, ISA bus, 640Kbytes RAM, unused COM port and DOS Version 3.1 or later
- Printer with Centronics parallel interface and cable with DB25 connector.

Monitoring Software:
TLR+ interfaces with Monitoring software in Native mode, Ademco™ 685 emulation mode and SurGard™ MLR2 emulation mode.

Optional remote control MRD1000

- Displays incoming signals or controls on 2 lines by 20 characters.
- Configures and operates a TLR+ or a SA-TLR+.
- Alarm acknowledge key for easy operation.
- Powered by TLR+ or SA-TLR+.
- External self contained unit or Mounted in PC’s CD slot
FAQ ON INTERNAL RECEIVERS